How To Bend Acrylic

How to bend Acrylic/Perspex: The best way to bend acrylic is to use a strip heater with an element running between two watercooled tubes, preferably made from stainless steel. These tubes should be adjustable so that the gap between the two tubes can be increased or decreased depending upon the thickness of material that you are bending.

Super Adhesive May Have Many Industrial Uses - Learning from Geckos

Science works fast, especially when it comes to adhesives. A few years back, the BBC Wildlife magazine published a little story on gecko lizards. They referred to the little creatures as cling kings because they're known to cling to surfaces even when the surface is held upside down. The year was 2002, and scientists were just beginning to speculate that the trick wasn't in what appeared to be little suction cups on their toes and feet as had always been believed. In fact, the scientists continued, those little suction pads were too small to generate enough suction to adhere them to any surface. No, suction didn't account for the adhesive quality of the little gecko.

Polyester Prices Are Rising In The Textile Market

The prices of man-made fibers intermediates were largely governed by the volatile crude oil values in 2006. Oil prices rose significantly by 18-20% during the year. This was over and above the 36-40% increase recorded in 2005. The surge is attributed to geo-political issues and unrest in the middle-east.

Choosing A Fine Bubble Diffuser - Disc Diffuser - Tube Diffuser Or Panel Diffuser?

Selecting a fine bubble aeration system used to be a choice between a membrane or ceramic disc. Today there are discs, tubes, and panels, and one needs some guidance in selecting the proper diffuser for the job.

Mechanical Contractors

A mechanical contractor is needed for those big jobs. The right one can install heavy equipment and keep it running properly. Everyone's equipment needs are different. If you require heavy equipment installation of any kind, a licensed mechanical contractor is an important person to have on your team.

How to Use a Binding Machine

Most bound documents last longer than unbound documents. Binding is a procedure by which pages and cover of a book are bound together through a strip sewn over or along an edge of a book for strengthening or decoration. Current binding processes are done mostly with machines rather than manually, for greater efficiency and better finishing.

Wooden Pallets

Wooden pallets are basically strong and rigid platforms. They are primarily used to provide support to various goods that are required to be shipped from one place to another, thus, avoiding any possible damage to the goods. A number of people might be surprised to know that the wooden pallet industry itself is an extremely crucial part of the American economy. The number of pallets used every day, that is the daily requirement of wooden pallets is a staggering 2 billion. The reason for this overwhelming figure is probably the universality of the requirement of the product. These pallets are used not just for packing, but also for stacking goods safely before they are lifted up.

An Introduction To Wire EDM

EDM refers to wire electrical discharge machining. Wire electrical discharge machining or EDM is a metalworking process with the help of which a material is separated from a conductive work piece, by means of electrical erosion. The wire never comes in contact with the conductive work piece. The wire electrode leaves a path on the work piece, which is slightly larger than the wire. Most often a 0.010' wire is used which creates a 0.013' to 0.014' gap. The wire electrode once passed through the work piece cannot be reused.

Used Wire EDM Machines

The oscillating of the U.S. economy has provided many great deals for used wire EDM machines, which include all major and reputed brands. Primarily, before investing in a used Wire EDM it is essential to verify the integrity and reputation of the business. In the same vein, one must be sure that the company he is doing business with, is trustworthy. It is advisable to decide what product is to be manufactured, the quantity, size and capacity of the tank required and the details of the cuts required. Different machines allow different axis paths through which the wire can travel. It is advisable to purchase a wire EDM that would suit the specifications and requirements.

Wire EDM FAQs

Wire electrical discharge machining is a method of cutting conductive materials with a traveling wire that separates material in a controlled manner. The wire used is electrically charged and actually arcs with the part to be cut.

Aerospace Machine Shops

Aerospace machine shops produce complex machinery such as high precision satellites and scientific instruments. This machinery is used in various arenas of space research and other programs that use aerospace as their field of study and performance.

EDM Machining

EDM machining actually stands for electrical discharge machining. This is the term used for a machining process that is used in the process of manufacturing those parts that are made from very hard metals and their alloys. Some of the parts or objects that are produced with the use of EDM machining include dies made of hardened steel, critical components of engines and compressor blades of jet engine fans. EDM machining is a thermal process that is able to remove as well as re-deposit material on top of the object that is being machined. The area that is recast is characteristically much tougher than the regular or original surface. It also will have a desirably higher resistance to wear and tear like abrasion and corrosion.

Air Purifier & Air Cleaner OEM Production

Finding an OEM solution for air purifier & air cleaner